Heavy Duty Forklift 10 Ton Diesel CPCD100 Hydraulic Fork Positioner, CE, Steel & Stone Yard, FOB
TAVOL CPCD100 — 10,000 kg diesel counterbalance forklift for steel, stone and precast yards. 600 mm load centre, 3,000 mm 2-stage duplex mast, 1,520 mm forks on solid tyres, hydraulic fork positioner controlled from the operator seat, FAW Wuxi Xichai CA6110 six-cylinder 85 kW engine with auto-hydraulic transmission. MOQ 1 set · 24-month warranty · FOB / CIF.
Tavol CPCD100 diesel forklift carries 10 tonnes at a 600 mm load centre and lifts 3 metres on a two-stage duplex mast. It is specified for steel service centres, stone yards and precast plants, where loads are dense, footprints are awkward and the machine has to keep working through the shift.
Production is in-house at our Tai'an factory. Standard builds ship in 5 days, customised builds in about 15 working days, and OEM or ODM branding is accepted. Tell us the load and the yard, and we quote the configuration rather than a generic model.
Overview
Loading ten tonnes all day in a steel or stone yard? The CPCD100 is put together so the operation does not stop: an 85 kW FAW Wuxi Xichai CA6110 six-cylinder diesel driving through an auto-hydraulic transmission, 1,520 mm forks on solid 9.00-20NHS tyres, and a hydraulic fork positioner that sets fork spread from the driver's seat. 13,850 kg of service weight is what holds a 10 t load at full lift — no auxiliary ballast, no derating tricks.
At a glance
10,000 kg — rated capacity at a 600 mm load centre
600 mm — load centre
3,000 mm — lift height, two-stage duplex mast
4,150 mm — minimum turning radius
15 / 20 km/h — travel speed, laden / unladen
2,245 mm — overall width
Design highlights
01 — Ten tonnes at the stated load centre
The rating is quoted at 600 mm, so the number on the plate is the number you can lift — derating starts only when the load sits further out.
02 — 85 kW, six cylinders, no clutch
Torque arrives at low engine speed, and direction changes are hydraulic. Loaded ramp starts do not depend on revving the engine or on clutch technique.
03 — Fork spread from the driver's seat
The hydraulic fork positioner moves the carriage by cylinder, not by hand. A coil, a stone block and a precast segment can share the same shift without stopping to re-pin the forks.
04 — Solid tyres on a yard that eats rubber
9.00-20NHS solid tyres with 250 mm ground clearance remove the puncture failure mode on surfaces carrying scrap, slag and offcuts.
Component details
Four components decide how the machine behaves after a year of shifts. Captions are given in Chinese and English on the images.
Cushioned lift and tilt cylinders. The cylinders buffer the end of travel, so the mast stops without the jolt that shakes the load and the operator.
Large-bore hydraulic manifold. Large-diameter lines combined with load sensing and two-way confluence cut what the pump has to deliver on every working cycle. Wider steering angle. Steering axle geometry reduces the turning radius — the difference between a three-point shunt and one clean turn in a tight aisle.
Cast steel axle housing. Drum brake as standard, wet brake optional. The reinforced housing deflects less under load and is built dust-proof and water-proof. Load-adaptive gearbox. Output torque and speed follow the external load, absorbing the impact and vibration that would otherwise reach the driveline.
Console layout. Standard electro-hydraulic direction control, shift logic that prevents starting in second gear, and an instrument cluster that shows running status and fault information.
Why operators keep choosing it
10 t capacity quoted at a 600 mm load centre
1,520 mm forks matching coil, slab and precast footprints
85 kW six-cylinder engine with an auto-hydraulic transmission
300 mm/s lift speed under full load
Solid tyres with 250 mm ground clearance
Hydraulic fork positioner, side shift available as a combined carriage
CE and ISO 9001 certified; special equipment manufacturing licence held
24-month warranty with free replacement parts during the term
Specification
Values are for the standard configuration of CPCD100.
Drawing key: L overall length, W overall width, H mast height, H1 overhead guard height, r turning radius, a/2 and b clearance figures. The final envelope is confirmed on the order drawing, because mast type, fork length and attachment each change it.
Colour, customization & support
Built to your specification
Red, green or custom colour
Forks 1,220 / 1,370 / 1,520 / 1,670 / 1,820 mm
Mast: 2-stage duplex 3 m standard; duplex full-free and 3-stage triplex on request
Attachment: fork positioner, side shifter, combined positioner + side shift, rotator, clamps
Tyres: solid standard, pneumatic and non-marking on request
Cab, heater, air conditioner, high-level exhaust, suspension seat and camera
OEM branding and packaging available
What comes with the machine
24-month warranty, replacement parts free of charge during the term
Reply within 24 hours, technical support 7x24
Full spare-parts line held for the whole range
Engineers travel to your market for commissioning and operator training
Pre-sales configuration design, in-sales order tracking and logistics
FOB or CIF terms; T/T, letter of credit or online bank payment
Specifications are for reference and may be revised without notice; confirm the final configuration on your order.
